Troubleshooting

Fix Common Commercial LED Lighting Problems

Flickering fixtures, lights that won’t turn on, or a sudden buzz overhead — here’s what usually causes it, and how to know when it’s time to call a licensed electrician.

Before you start

Never open a fixture, ballast, or driver while it's connected to power. If a light is hot to the touch, sparking, or smells like burning, shut off the breaker and call us right away — don't attempt a DIY fix.

01

Lights Are Flickering

Every install is carried out by licensed electrical contractors for optimal performance and longevity.

Likely Causes

  • Incompatible or failing dimmer switch
  • Loose wiring connection at the fixture or panel
  • Driver mismatched to fixture wattage
  • Voltage fluctuation on a shared circuit
What to Check

1

Check the dimmer

Confirm it’s rated for LED loads — not all dimmers are compatible with LED drivers.

2

Tighten connections

With power off, check that wire nuts and fixture terminals are seated firmly.

3

Isolate the circuit

See if the flicker follows one fixture or the whole circuit — this tells us where the fault lives.

Flicker continues after these checks?

02

Fixture Won't Turn On

Before assuming the fixture has failed, rule out the simpler upstream causes — they account for most no-power calls.

Likely Causes

  • Tripped breaker or blown fuse
  • Failed photocell or timer (exterior lighting)
  • Bad driver inside the fixture
  • Damaged wiring from moisture intrusion
What to Check

1

Check the panel

Look for a tripped breaker and reset it once, fully off then on.

2

Test the photocell

For exterior fixtures, cover the sensor if it doesn’t trigger the light, the photocell may be the issue.

3

Inspect for water damage

Look for condensation or corrosion inside the fixture housing, especially after storms.

Breaker trips again after reset?

03

Lights Are Dim or Fading

LEDs degrade gradually over their rated life, but a sudden drop in brightness usually points to something else.

Likely Causes

  • Fixture nearing end of rated lifespan
  • Heat buildup inside the housing
  • Voltage drop on a long circuit run
  • Dirt or debris on the lens
What to Check

1

Clean the lens

Dust and grime on parking lot and warehouse fixtures can noticeably cut output.

2

Check install date

Compare current brightness against the fixture’s rated lifespan and lumen depreciation curve.

3

Look for heat buildup

Blocked vents or enclosed housings can shorten a driver’s life significantly.

Dimming across multiple fixtures?

04

Buzzing or Humming Sound

A faint hum can be normal, but a loud or growing buzz is a sign something in the fixture needs attention.

Likely Causes

  • Incompatible dimmer causing electrical noise
  • Failing or overloaded driver
  • Loose fixture components vibrating
  • Old, non-LED-rated transformer left in place
What to Check

1

Note when it happens

Constant hum vs. only when dimmed points to different causes.

2

Check mounting hardware

Loose brackets or trim rings can rattle and sound like a fixture issue.

3

Rule out old transformers

Leftover fixtures from a fluorescent-to-LED conversion sometimes keep an incompatible ballast in the circuit.

Buzz is loud or getting worse?

05

Color Shifting or Uneven Tone

Mismatched color temperature across a property usually traces back to mixed product generations rather than a defect.

Likely Causes

  • Mixed fixture batches or manufacturers
  • Phosphor degradation in older LEDs
  • Wrong Kelvin rating ordered for a replacement
  • Dimmer causing color shift at lower output
What to Check

1

Check the Kelvin rating

Confirm replacement fixtures match the original spec (e.g. 4000K vs 5000K).

2

Compare fixture age

Older LEDs can shift warmer as phosphors degrade — newer units nearby will look cooler by comparison.

3

Group by manufacturer

Where possible, replace in matching sets rather than mixing brands on the same run.

Planning a phased retrofit?

17

Years in Business

75%

Max Energy Savings

70%

Utility Incentives Available

<2 yrs

Typical Payback Period

Still Not Fixed?

Let Our Licensed Team Take a Look

If the issue isn’t resolved after these checks, our electricians can diagnose it on-site and give you a clear, no-pressure recommendation.